Enhancements for the Dillon XL 750 Press
|.32 Cal. Wad Cutter Powder Funnel (SKU: T1672-05)Specifically designed for loading wad cutter bullets in .32 S&W Long for Bullseye competition. It provides full length case expansion for loading Hollow Base Wadcutter bullets … preventing swaging the bullet base.||
.32 Caliber Powder Funnels (SKU: T1672)The Custom Rifle Powder Funnel for .32 cal. pistol cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+.
||.45 HTC Powder Funnel (SKU: T1740)This Powder Funnel was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek).||2X Powder Hopper Tube (SKU: T1277)The 2X Powder Hopper Tube™ doubles the powder capacity of the Dillon Auto Powder Measure or "Belted Magnum" Powder System.|
|38 Spl. Wadcutter Powder Funnels (SKU: T1735)These Powder Funnels are specially designed for the needs of bullsey shooters loading Double Ended Wad Cutter (DEWC) or Hollow Base Wad Cutter (HBWC) bullets in .38 Special cartridges.||
550/750 Primer Feed Stop (SKU: T1742)This Primer Feed Stop allows you to temporarily disable the
||650/750 Bearing Camming Pin (SKU: T1706)||650/750 Case Feed Stop Switch (SKU: T1704)|
|650/750 Spent Primer Chute (SKU: T1346-650)The 650/750 Spent Primer Chute™ replaces the blue plastic spent primer cup and bracket on Dillon XL 650 and XL 750 reloading presses. Spent primers are routed through clear PVC tubing into any convenient waste container, so spent primes simply can't bounce out onto the floor! Includes 650/750 Primer Chute™, 3' Clear PVC Tubing and Instructions. Note: Does not fit certain older model 650 presses. See product page for details before ordering.||750 FailSafe Bracket Kit (SKU: T1746)This 750 FailSafe Bracket features slotted screw holes that allow the Powder Measure to be rotated enough (about 12 degrees) that the powder bar clears bullet droppers, micrometer seat dies and other extra-tall dies in Stations 3 & 4. from the Failsafe Bracket! At 1/4″ thick, it is very strong and rigid … ensuring that your powder bar returns fully every time.||9mm/.38 HTC Powder Funnel (SKU: T1736)This Powder Funnel was specially designed for loading 9mm cast/coated bullets sized to 0.358″ OD, that would provide for minimum swaging of the bullet’s base. Sized for projectiles up to 0.358″ diameter … preventing shaving polymer bullet coatings (e.g. Hi-Tek).||Arredondo Powder Drop Slide with Micrometer (SKU: T1267)The Arredondo Accessories Powder Drop Slide with our Micrometer Powder Bar Kit preinstalled. For the Dillon Precision auto powder measure. See product page to order the correct version for your press.|
|Bin-Shelf (SKU: T1633)The Bin-Shelf™ provides a platform to support the weight of the Cartridge Bin on Dillon XL 650 and XL 750 presses.||Brass Primer Magazine Tube Ends (SKU: T1739)These Brass Primer Magazine Tube Ends replace the plastic "Flexible Orifice" on Dillon Primer Magazine Tubes for RL 550 and XL 750 presses.||
Bulk Powder Feed Kit (SKU: T1676)The Bulk Powder Feed™ Kit continuously refills your powder measure, keeping your powder hopper at a constant full level. It gravity feeds gunpowder directly from an 8lb or 4lb container.
||Bullet Seat Stem (SKU: T1561)This custom bullet seat stem contacts SWC bullets at the shoulder, yielding consistent alignment and seating of SWC bullet profiles. Works equally well with FWC bullets! Fits Dillon "New Dynamic" Pistol Seat Die. Available in .45 cal., .40 cal. and .38 cal. (See web page to select the caliber you need.)|
|CNC Machined 550/650 Toolheads (SKU: T1333)CNC machined toolheads for Dillon RL 550, XL 650 and XL 750 reloading presses. Made from solid 6061-T6 aluminum and machined to exacting standards.||Component Recovery Cup (SKU: T1668)Component Recovery Cup™ separates powder from bullet and case when pulling bullets. Powder drains directly back into powder measure hopper for immediate reuse.||
Custom Powder Funnel (SKU: T1582)The Custom Powder Funnel supplied is precision machined from top grade 12L14 Steel and hardened to RC55+ … offering an almost unlimited life time of use. The mirror finish of this part yields minimal friction and a smoother release.
These Custom Powder Funnels work so well, you may want to use them on all your pistol cartridge toolheads … even toolheads that are not set up for a Mr. Bulletfeeder!
|Die Wrench for Dillon Presses (SKU: T1532)The best and last die wrench you'll ever need for your Dillon press. Fits Both 1″ and 1-1/8″ Die Lock Rings.|
|Dillon Primer Rod with Holder (SKU: T1562)Dillon Primer Rod with Holder. The Primer Rod is made from aluminum and weighs 0.52oz to give positive primer feeding. The Primer Rod has lines at 100 primers, 75 primers, 50 primers and 25 primers and is accurate to ±1 primer. Also included is a Primer Rod Holder, so when you load primers into the tube, you have a convenient place to hang the Rod. Fits on Dillon Squared Deal 'B', RL 550, XL 650, XL 750, RL 1050, Super 1050 and RL 1100 presses.||Dillon XL 650/750 Case Chute Extension (SKU: T1590)The Dillon XL 650 Case Chute Extension lenghtens the original cartridge ejection chute by 6.25″, allowing you to use a larger container to capture the loaded cartridges. Just set any convenient container on the bench and position it under the chute. Note: Press must be on a Strong Mount.||Extended Die Lock Nuts (SKU: T1745)Extended die lock nuts for when you need to put the die lock nut on the bottom of the toolhead. A 0.155″ shoulder gets the hex nut corners clear of the press frame.||Floating Die 550/650 Toolheads (SKU: T1389)CNC Machined Floating Die Toolheads for Dillon RL 550, XL 650 and XL 750 presses. Size Die and Bullet Seat Die are floated for improved ammunition concentricity. Available only with Toolhead Clamp Kit™ parts pre-installed.|
|Foam Grip (SKU: T1527)This foam grip cushions your hand yet provides good "feel" when seating primers. Fits both the Plastic and Aluminum Dillon Roller Handles … as well as most other press handles that are approximately 1" diameter and 4" to 5" long.||Loaded Round Counter (SKU: T1555)The UniqueTek Loaded Round Counter is an electronic counter for your Dillon press that counts only successfully loaded rounds ... not just press cycles. Can also be used on many other reloading presses that have: 1) Have a Crimp Die with an open top, and 2) Have a primer magazine tube or similar place on which to mount the LCD Display Module.||Micrometer Powder Bar Kit (SKU: T1231)A micrometer conversion kit for the powder bar of your Dillon Auto Powder Measure.||Open End Die Wrench for Dillon Presses (SKU: T1733)An Ope-End Die Wrench for Dillon press. Fits Both 1″ and 1-1/8″ Die Lock Rings. Works on dies where a box-end wrench won't fit.|
|Powder Bar Spacer Bolt Kit (SKU: T1751)Replaces the white plastic Powder Bar Spacer Plugs (#13921) on Dillon Powder Measures. Clamps the Spacer solidly in place … so it can't creep back and forth as the powder bar cycles.||Powder Measure Drain-N-Change Tool (SKU: T1347)Powder Measure Drain-N-Change™ Tool. Allows users of Dillon reloading presses to drain gunpowder or change powder bars without removing the powder measure from the press or toolhead.||Powder Measure Quick Change, QD Tab (SKU: T1720)This Powder Measure Quick Change, QD Tab allows you to quickly and easily remove your Dillon powder measure … without any tools!||
Powder Measure Stand Adapter (SKU: T1573)The Powder Measure Stand Adapter allows you to store your spare Dillon Powder Measure on a RL550/XL650 Toolhead Stand.*
*Dillon Toolhead Stand not included.
|Precision Powder Baffle (SKU: T1278)Pecision Powder Baffle™ upgrade for Dillon powder measures.||Primer System Tag (SKU: T1747)This Primer System Tag clips onto the primer feed system housing and gives you a 1″ x 3″ area upon which you can write the primer type. Comes bundled with 100 Jewelry Tags to label your Primer Pickup Tubes.||Primer Tube Stand (SKU: T1567)The UniqueTek Primer Tube Stand holds up to 12 primer pickup tubes, 6 on each side, in a horizontal position. The Stand has a base that is wide enough to be stable and not easily tipped over. It assembles in just seconds and can easily be dismantled to save bench space when not in use.||
Rifle Powder Funnels (SKU: T1632)The Custom Rifle Powder Funnel for .30 cal. rifle cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+.
|Shellplate Bearing Kit (SKU: T1601)The 550/650/900 Shellplate Bearing Kit smooths indexing and reduces play and wobble in the shell plate. It also reduces the "snap" when the index ball engages the shellplate … greatly reducing powder loss from cases on the shellplate.||SkyLight LED Lighting Kit for Dillon 650/750 (SKU: T1670)This patent pending reloading press LED lighting system consists of a machined bushing with an embedde high output LED pod which installs into the center hole of the toolhead. Super bright, straight down focused light, out of the way, no heat and does the job perfectly. For Dillon XL 650 presses.||SOLO Single Stage Press Conversion Kit (SKU: T1553)The SOLO™ Single Stage Press Conversion Kit converts your Dillon RL 550b or XL 650 press to a single stage press. This allows you to perform reloading operations that simply cannot be done using a Dillon progressive reloading press. (See product web page for details and to order the correct kit for your press.)||Swage It S750 (SKU: T1568-7)The Swage It S750 Primer Pocket Swager for the Dillon XL 750 press. Everything that you need to swage .223/5.56mm, .308/7.62mm or any other calibers that utilize small or large primers. Includes Swages for both small and large primers.|
|The Bin-Dam (SKU: T1359)The Bin-Dam™ fits into the front of the Cartridge Collection Bin for Dillon, LEE and RCBS reloading presses. It keeps rounds from rolling out and onto the floor when the bin gets near full. Allows use of 100% of bin's capacity. Available in three sizes to fit the cartridge collection bins for SDB/550/650 presses, the 1050 press, and for the SL 900 Shotshell Loader.||The Bullet Bin (SKU: T1446)The Bullet Bin™ is an economical alternative to the Dillon Bullet Tray. Easily holds a full 500 count box of 9mm 124grain bullets ... with room to spare.||Toolhead Clamp Kit (SKU: T1230)The UniqueTek Toolhead Clamp Kit™ enables your Dillon 550, 650 and 750 toolheads, and RCBS Pro 2000®/Piggyback™ -3 & -4 dieplates, to be CLAMPED into the press frame. This corrects the loose fit between the toolhead and press frame, thus reducing OAL variation and improving die-to-shellplate alignment.||
Toolhead Organizer - 550/650/750 (SKU: T1629)Organize and store all your Dillon 550/650/750 toolhead assemblies and caliber conversion kits on one convenient place. Mounts to wall, freeing up more space on your work bench. Available in 3-post and 5-post models.