|"Advantage" 10/22 Charging Handle & Picatinny Scope Base (SKU: T1689)Precision machined picatinny rail for Ruger® 10/22® rifles. Features a left side Charging Handle to clear jams and charge the rifle without loosing trigger and stock position.||.32 ACP Case Gauge (SKU: T1557)Case Gauge for .32 ACP. Precision CNC Machined from Stainless Steel to SAAMI Minimum Chamber Specs.||.32 Cal. Wad Cutter Powder Funnel (SKU: T1672-05)Specifically designed for loading wad cutter bullets in .32 S&W Long for Bullseye competition. It provides full length case expansion for loading Hollow Base Wadcutter bullets … preventing swaging the bullet base.||
.32 Caliber Powder Funnels (SKU: T1672)The Custom Rifle Powder Funnel for .32 cal. pistol cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+.
||.45 HTC Powder Funnel (SKU: T1740)This Powder Funnel was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek). [T1740]||.45 HTC Powder Through Expander (SKU: T1729-04)This Powder Through Expander (PTX™) was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek).|
|.45 HTC-FB Powder Funnel (SKU: T1766)This Powder Funnel was specially designed for loading 180/185gr Flat Base SWC .45 caliber bullets sized to 0.452″ … like the Brazos Bullet Company LB-45-180-SWC-FB-LG-452. [T1766]||0.05-Grain Enhanced Electronic Powder Scale (SKU: T1391)The 0.05-Grain Powder Scale fills the gap between standard 0.1 grain accuracy scales, and high-precision 0.02 grain accuracy scales ... both in performance and price. It has 308 grain capacity with 0.05 grain accuracy||10/22 Extended Magazine Release (SKU: T1402)10/22 Extended Magazine Release is longer than the standard factory release, making it easier and faster to release the magazine on Ruger® 10/22® rifles. Drop-in fit requires no modification to the rifle. Avaialble in either black or stainless steel finish.||1050 Spent Primer Chute (SKU: T1346-1050)The 1050 Spent Primer Chute™ replaces the blue plastic spent primer cup on the Dillon Super 1050 reloading press. Spent primers are routed through clear PVC tubing into any convenient waste container.||
12GA to .357 Magnum Shotgun Adapter (SKU: T1698-03)This adapter gives your 12 Gauge single or double-barrel break action shotgun the ability to fire .38 Sp./.357 Mag. ammo. Rifled bore for better accuracy.
||1911 End Mill Bit Set (SKU: T1551)This bit set contains all the tooling to rough cut the 1911 frame and drill sear and hammer pin holes. Included: #22 Drill Bit, #35 Drill Bit, #52 Drill Bit, High Speed Steel 7/64″ Key Cutter and High Speed Steel 1/2″ End Mill. (NOTE: All these end mill bits are designed for use in an end mill. A drill press is not recommended.)|
|1911 Recoil Buffer (SKU: T1748-02)1911 Recoil Buffer. Reduces felt recoil, enhances muzzle control and stops slide to frame impact. (T1748-02 4 per pack)||22UpLULA (SKU: T1602)The 22UpLULA™ pistol mag. loader & unloader is designed to load .22LR wide-body pistol mags. > 1/2″, like .22LR 1911 mags and other .22LR converted mags. It has the body width of the UpLULA™ but has a narrower metal beak designed for .22LR rounds.||2X Powder Hopper Tube (SKU: T1277)The 2X Powder Hopper Tube™ doubles the powder capacity of the Dillon Auto Powder Measure or "Belted Magnum" Powder System.||38 Spl. Wadcutter Powder Funnels (SKU: T1735)These Powder Funnels are specially designed for the needs of bullsey shooters loading Double Ended Wad Cutter (DEWC) or Hollow Base Wad Cutter (HBWC) bullets in .38 Special cartridges.||550 Primer Track Bearing (SKU: T1571)The UniqueTek 550 Primer Track Bearing has a 1.4″ extension that supports the primer bar better. Prevents the primer bar from "drooping" and binding while its in the "out" position. It is a drop-in replacement and takes just minutes to install. NOW with ROBAR® NP3® Plating (a Nickel/Teflon composite).||550 Spent Primer Chute (SKU: T1346-550)The 550 Spent Primer Chute™ is a Spent Primer Chute for the Dillon RL 550B Press. Spent primers are routed through clear PVC tubing to any suitable container located under your reloading bench. Virtually eliminates spent primers bouncing out and onto the floor.|
550/750 Primer Feed Stop (SKU: T1742)This Primer Feed Stop allows you to temporarily disable the
||650 Bearing Indexer Block (SKU: T1705)This Bearing Indexer Block provides smoother operation of the Indexer Ring on Dillon XL 650 presses. It also eliminates wear of and the need to lubricate the Indexer Ring.|