Product List

Sort By:
.32 Caliber Powder Funnels (SKU: T1672).32 Caliber Powder Funnels (SKU: T1672)The Custom Rifle Powder Funnel for .32 cal. pistol cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+.
.45 HTC Powder Funnel (SKU: T1740).45 HTC Powder Funnel (SKU: T1740)This Powder Funnel was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek).
1050 Spent Primer Chute (SKU: T1346-1050)1050 Spent Primer Chute (SKU: T1346-1050)The 1050 Spent Primer Chute™ replaces the blue plastic spent primer cup on the Dillon Super 1050 reloading press. Spent primers are routed through clear PVC tubing into any convenient waste container.
2X Powder Hopper Tube (SKU: T1277)2X Powder Hopper Tube (SKU: T1277)The 2X Powder Hopper Tube™ doubles the powder capacity of the Dillon Auto Powder Measure or "Belted Magnum" Powder System.
38 Spl. Wadcutter Powder Funnels (SKU: T1735)38 Spl. Wadcutter Powder Funnels (SKU: T1735)These Powder Funnels are specially designed for the needs of bullsey shooters loading Double Ended Wad Cutter (DEWC) or Hollow Base Wad Cutter (HBWC) bullets in .38 Special cartridges.
550 Primer Track Bearing (SKU: T1571)550 Primer Track Bearing (SKU: T1571)The UniqueTek 550 Primer Track Bearing has a 1.4″ extension that supports the primer bar better. Prevents the primer bar from "drooping" and binding while its in the "out" position. It is a drop-in replacement and takes just minutes to install. NOW with ROBAR® NP3® Plating (a Nickel/Teflon composite).
550 Spent Primer Chute (SKU: T1346-550)550 Spent Primer Chute (SKU: T1346-550)The 550 Spent Primer Chute™ is a Spent Primer Chute for the Dillon RL 550B Press. Spent primers are routed through clear PVC tubing to any suitable container located under your reloading bench. Virtually eliminates spent primers bouncing out and onto the floor.
550/750 Primer Feed Stop (SKU: T1742)550/750 Primer Feed Stop (SKU: T1742)This Primer Feed Stop allows you to temporarily disable the RL 550 or XL 750 Primer System. It simply drops on top of the Primer Slide and keeps it in the out position. Perfect for when you are loading pre-primed brass.
650 Bearing Indexer Block (SKU: T1705)650 Bearing Indexer Block (SKU: T1705)This Bearing Indexer Block provides smoother operation of the Indexer Ring on Dillon XL 650 presses. It also eliminates wear of and the need to lubricate the Indexer Ring.
650 FailSafe Bracket Kit (SKU: T1677)650 FailSafe Bracket Kit (SKU: T1677)This FailSafe Bracket is machined from 1/4″ 303 Stainless Steel. It is very strong and rigid … ensuring that your powder bar returns fully every time. Plus it features a brass shoulder washer that is held in place with set screws … ensuring that the shoulder washer can't disengage from the Failsafe Bracket!
650 Live Primer Chute (SKU: T1306)650 Live Primer Chute (SKU: T1306)The UniqueTek 650 Live Primer Chute Prevents primers from falling onto floor. It captures primers and holds them for reuse. The UniqueTek 650 Live Primer Chute is a "drop-in" replacement for the original Dillon Primer Chute (part #16210) and takes just minutes to install. (Note: May not fit certain older XL 650 presses. See product web page for complete details.)
650 Primer Feed Stop Switch (SKU: T1703)650 Primer Feed Stop Switch (SKU: T1703)This Primer Feed Stop Switch allows you to temporarily disable the XL 650 Primer System. It simply replaces the original Primer Cam and can be switched from ON to OFF in just a few seconds without any tools.
650/750 Bearing Camming Pin (SKU: T1706)650/750 Bearing Camming Pin (SKU: T1706)
650/750 Case Feed Stop Switch (SKU: T1704)650/750 Case Feed Stop Switch (SKU: T1704)
750 FailSafe Bracket Kit (SKU: T1746)750 FailSafe Bracket Kit (SKU: T1746)This 750 FailSafe Bracket features slotted screw holes that allow the Powder Measure to be rotated enough (about 12 degrees) that the powder bar clears bullet droppers, micrometer seat dies and other extra-tall dies in Stations 3 & 4. from the Failsafe Bracket! At 1/4″ thick, it is very strong and rigid … ensuring that your powder bar returns fully every time.
9mm/.38 HTC Powder Funnel (SKU: T1736)9mm/.38 HTC Powder Funnel (SKU: T1736)This Powder Funnel was specially designed for loading 9mm cast/coated bullets sized to 0.358″ OD, that would provide for minimum swaging of the bullet’s base. Sized for projectiles up to 0.358″ diameter … preventing shaving polymer bullet coatings (e.g. Hi-Tek).
Arredondo Powder Drop Slide with Micrometer (SKU: T1267)Arredondo Powder Drop Slide with Micrometer (SKU: T1267)The Arredondo Accessories Powder Drop Slide with our Micrometer Powder Bar Kit preinstalled. For the Dillon Precision auto powder measure. See product page to order the correct version for your press.
Bin-Shelf (SKU: T1633)Bin-Shelf (SKU: T1633)The Bin-Shelf™ provides a platform to support the weight of the Cartridge Bin on Dillon XL 650 presses.
Brass Primer Magazine Tube Ends (SKU: T1739)Brass Primer Magazine Tube Ends (SKU: T1739)These Brass Primer Magazine Tube Ends replace the plastic "Flexible Orifice" on Dillon Primer Magazine Tubes for RL 550 and XL 750 presses.
Bulk Powder Feed Kit (SKU: T1676)Bulk Powder Feed Kit (SKU: T1676)The Bulk Powder Feed™ Kit continuously refills your powder measure, keeping your powder hopper at a constant full level. It gravity feeds gunpowder directly from an 8lb or 4lb container.
1 2 3
Content © 2003-2020 UniqueTek, Inc.