|.32 Cal. Wad Cutter Powder Funnel (SKU: T1672-05)Specifically designed for loading wad cutter bullets in .32 S&W Long for Bullseye competition. It provides full length case expansion for loading Hollow Base Wadcutter bullets … preventing swaging the bullet base.||
.32 Caliber Powder Funnels (SKU: T1672)The Custom Rifle Powder Funnel for .32 cal. pistol cartridges. Smoother interior for smooth powder flow and less powder bridging. Precision machined from top grade 12L14 Steel and hardened to RC55+.
||.45 HTC Powder Funnel (SKU: T1740)This Powder Funnel was specially designed for loading .45 caliber cast/coated bullets sized to 0.451″ to 0.452″ OD, that would provide for minimum swaging of the bullet’s base and preventing shaving polymer bullet coatings (e.g. Hi-Tek).||2X Powder Hopper Tube (SKU: T1277)The 2X Powder Hopper Tube™ doubles the powder capacity of the Dillon Auto Powder Measure or "Belted Magnum" Powder System.||38 Spl. Wadcutter Powder Funnels (SKU: T1735)These Powder Funnels are specially designed for the needs of bullsey shooters loading Double Ended Wad Cutter (DEWC) or Hollow Base Wad Cutter (HBWC) bullets in .38 Special cartridges.||550 Primer Track Bearing (SKU: T1571)The UniqueTek 550 Primer Track Bearing has a 1.4″ extension that supports the primer bar better. Prevents the primer bar from "drooping" and binding while its in the "out" position. It is a drop-in replacement and takes just minutes to install. NOW with ROBAR® NP3® Plating (a Nickel/Teflon composite).|
|550 Spent Primer Chute (SKU: T1346-550)The 550 Spent Primer Chute™ is a Spent Primer Chute for the Dillon RL 550B Press. Spent primers are routed through clear PVC tubing to any suitable container located under your reloading bench. Virtually eliminates spent primers bouncing out and onto the floor.||
550/750 Primer Feed Stop (SKU: T1742)This Primer Feed Stop allows you to temporarily disable the
||650 FailSafe Bracket Kit (SKU: T1677)This FailSafe Bracket is machined from 1/4″ 303 Stainless Steel. It is very strong and rigid … ensuring that your powder bar returns fully every time. Plus it features a brass shoulder washer that is held in place with set screws … ensuring that the shoulder washer can't disengage from the Failsafe Bracket!||750 FailSafe Bracket Kit (SKU: T1746)This 750 FailSafe Bracket features slotted screw holes that allow the Powder Measure to be rotated enough (about 12 degrees) that the powder bar clears bullet droppers, micrometer seat dies and other extra-tall dies in Stations 3 & 4. from the Failsafe Bracket! At 1/4″ thick, it is very strong and rigid … ensuring that your powder bar returns fully every time.||9mm/.38 HTC Powder Funnel (SKU: T1736)This Powder Funnel was specially designed for loading 9mm cast/coated bullets sized to 0.358″ OD, that would provide for minimum swaging of the bullet’s base. Sized for projectiles up to 0.358″ diameter … preventing shaving polymer bullet coatings (e.g. Hi-Tek).||Arredondo Powder Drop Slide with Micrometer (SKU: T1267)The Arredondo Accessories Powder Drop Slide with our Micrometer Powder Bar Kit preinstalled. For the Dillon Precision auto powder measure. See product page to order the correct version for your press.|
|Bin-Shelf (SKU: T1633)The Bin-Shelf™ provides a platform to support the weight of the Cartridge Bin on Dillon XL 650 and XL 750 presses.||Brass Primer Magazine Tube Ends (SKU: T1739)These Brass Primer Magazine Tube Ends replace the plastic "Flexible Orifice" on Dillon Primer Magazine Tubes for RL 550 and XL 750 presses.||
Bulk Powder Feed Kit (SKU: T1676)The Bulk Powder Feed™ Kit continuously refills your powder measure, keeping your powder hopper at a constant full level. It gravity feeds gunpowder directly from an 8lb or 4lb container.
||Bullet Seat Stem (SKU: T1561)This custom bullet seat stem contacts SWC bullets at the shoulder, yielding consistent alignment and seating of SWC bullet profiles. Works equally well with FWC bullets! Fits Dillon "New Dynamic" Pistol Seat Die. Available in .45 cal., .40 cal. and .38 cal. (See web page to select the caliber you need.)||CNC Machined 550/650 Toolheads (SKU: T1333)CNC machined toolheads for Dillon RL 550, XL 650 and XL 750 reloading presses. Made from solid 6061-T6 aluminum and machined to exacting standards.||Component Recovery Cup (SKU: T1668)Component Recovery Cup™ separates powder from bullet and case when pulling bullets. Powder drains directly back into powder measure hopper for immediate reuse.|
Custom Powder Funnel (SKU: T1582)The Custom Powder Funnel supplied is precision machined from top grade 12L14 Steel and hardened to RC55+ … offering an almost unlimited life time of use. The mirror finish of this part yields minimal friction and a smoother release.
These Custom Powder Funnels work so well, you may want to use them on all your pistol cartridge toolheads … even toolheads that are not set up for a Mr. Bulletfeeder!
|Die Wrench for Dillon Presses (SKU: T1532)The best and last die wrench you'll ever need for your Dillon press. Fits Both 1″ and 1-1/8″ Die Lock Rings.|